A crude oil assay report shows the potential yield of each boiling range fraction in a specific crude, along with the quality of each fraction. Refiners use the results of a crude assay to estimate how a grade will run through their units, and traders use them to evaluate what a cargo is worth.
While report layouts vary across laboratories and crude grades, most follow a consistent general sequence. Knowing what each section measures, and which standard test method produced each result, makes the data easier to review before it goes into a planning model, a valuation, or a blend decision. The sections below follow that order, then compare full assays with short assays and flash assays.
Crude Oil Assay Report Structure
Most reports open with identifying details: the crude name or grade, its origin, where and when the sample was taken. An assay describes the sample that was tested, so its usefulness depends on how well that sample represents the cargo, tank, or stream you are evaluating.
From there, the data usually falls into three layers:
- Whole-crude properties describe the crude as received, before it is separated into fractions.
- The distillation and yield table shows the share of the crude in each boiling range.
- Cut-by-cut data reports the properties of each individual fraction, from the lightest naphtha to the vacuum residue.
Many reports also include a light ends breakdown, a full boiling point curve, and additional residue data. Crude oil characterization at this level of detail supports refinery engineering, marketing decisions, and it helps monitor crude streams that change over time.
Whole-Crude Properties and What They Indicate
Traders and crude buyers often use whole-crude values as an initial screen, since they show quickly whether a grade fits a refinery’s limits on sulfur, acidity, and metals before anyone looks at individual cuts.
The table below lists properties commonly reported at the whole-crude level, the units they usually appear in, and a standard test method associated with each. Depending on the crude and where it is headed, a report may also include hydrogen sulfide, mercaptan sulfur, trace mercury, or amines, all of which are part of AmSpec’s crude oil testing services.
| Property | What it signals | Typical units | Common test method |
| API gravity and density | How light or heavy the crude is; also used to convert between mass and volume | °API; kg/m³ | ASTM D5002ASTM D4052 |
| Sulfur | Load on hydrotreating and sulfur recovery units | mass % | ASTM D4294ASTM D2622 |
| Total acid number (TAN) | Acidic content, often used to screen for corrosion risk in distillation units | mg KOH/g | ASTM D664ASTM D8045 |
| Pour point | An indication of the lowest temperature at which the crude can be handled for certain applications | °C / °F | ASTM D5853ASTM D97 |
| Water | Affects net volume in the purchase, sale, or transfer of the crude | mass % or volume % | ASTM D4928 |
| Salt (as chloride) | Whether the crude needs desalting, and the related corrosion risk | PTB (lb/1,000 bbl) or g/m³ | ASTM D3230 |
| Nickel, vanadium, and iron | Potential for catalyst deactivation during processing | mg/kg | ASTM D5708IP 501 |
| Carbon residue | An indication of the crude’s tendency to form coke | mass % | ASTM D4530 |
Units vary between laboratories and regions, so confirm whether density is reported at 15 °C or 60 °F and whether salt appears in PTB or grams per cubic meter before comparing reports. Pour point requires a closer look on waxy crudes, because ASTM D5853 includes procedures for both a maximum and a minimum pour point. Together they give a temperature window in which the crude, depending on its thermal history, may behave as a liquid or a solid.
Whole-crude values also describe an average. Sulfur, metals, and carbon residue tend to concentrate in the heavier fractions, so the distillate cut data show which specific fractions carry them.
Reading the Distillation and Yield Table
The yield table is one of the most closely read parts of the report. In a full assay and short assay, the crude is physically separated in two stages. ASTM D2892, the 15-theoretical plate column distillation commonly referred to as true boiling point (TBP) distillation, separates the crude up to a final cut temperature of 400 °C (752°F) atmospheric equivalent temperature (AET). The atmospheric resid is then distilled under vacuum by ASTM D5236, which can reach about 565 °C (1049°F) AET for most samples. Material that has not been distilled by that temperature is reported as vacuum residue.
ASTM D2892 and D5236 determine fraction yields by both mass and volume. The layout below lists the fractions a yield table commonly includes and how each one is typically used.
| Fraction | What the yield indicates | Common refinery destination |
| Light ends (through butanes) | Gas and LPG content | Gas recovery and LPG |
| Light naphtha | Light gasoline blending potential | Isomerization or gasoline blending |
| Heavy naphtha | Reformer feed potential | Catalytic reforming |
| Kerosene | Jet fuel and kerosene potential | Kerosene and jet fuel treating |
| Diesel or atmospheric gas oil | Middle distillate potential | Diesel hydrotreating |
| Vacuum gas oil | Conversion unit feed | Fluid catalytic cracking or hydrocracking |
| Vacuum residue | Share of the barrel left at the bottom | Coking, asphalt, or residual fuel |
ASTM D2892 and D5236 distillations require that cut point temperatures must be agreed on before the distillations begin, since refiners and traders do not all define fractions the same way. For example, a diesel yield on one report may cover a different boiling range than the diesel yield on another report.
Next, confirm the basis. Mass and volume yields for the same cut can differ noticeably, especially at the light and heavy ends of the barrel, and a planning model or pricing tool may expect one or the other. Then check how the yields add up. The cuts, plus any reported loss, should account for the full sample.
Some reports also include a high temperature simulated distillation (SimDis) curve from ASTM D7169, a gas chromatography method that determines boiling point distribution through 720 °C (1328°F). It extends the curve past the vacuum distillation limit and offers a useful cross-check, although its results are not directly interchangeable with physical distillation data, and it does not produce physical fractions for further testing.
Cut-by-Cut Data for Each Fraction
Cut data answers a narrower question than the whole-crude block: how well each cut suits the unit it will feed, and what that unit will need to remove or adjust along the way.
| Fraction | Properties often reported | Example test methods |
| Naphtha | Density, sulfur, and hydrocarbon type (paraffins, naphthenes, and aromatics) | ASTM D4052 (API)ASTM D4294 (sulfur)ASTM D6730 (PONA) |
| Kerosene | Smoke point, freeze point, sulfur, and aromatics | ASTM D1322 (smoke point)ASTM D2386 (freeze point)ASTM D4294 (sulfur)ASTM D1319 (FIA) |
| Diesel or Atmospheric gas oil | Cloud point, pour point, cold filter plugging point, sulfur, and cetane index | ASTM D2500 (cloud point), ASTM D97 (pour point), ASTM D6371 (CFPP)ASTM D4294 (sulfur)ASTM D976 (cetane index) |
| Vacuum gas oil | Sulfur, nitrogen, metals, and carbon residue | ASTM D4294 (sulfur)ASTM D5762 (nitrogen)ASTM D5708 (metals)ASTM D4530 (carbon residue) |
| Vacuum residue | Carbon residue, metals, asphaltenes, and viscosity | ASTM D4530 (carbon residue), ASTM D5708 (metals) ASTM D6560 (asphaltenes)ASTM D445 (viscosity) |
In the lighter cuts, the focus is product quality. Kerosene smoke point is tied to hydrocarbon composition, and ASTM D1322 notes that more aromatic fuels generally produce a smokier flame, which matters for jet fuel. In the diesel range, cloud point, pour point, and CFPP describe cold flow behavior, the same properties examined in middle distillate testing of finished fuels.
Further down the barrel, the focus shifts to contaminants and processing load. Nitrogen compounds can contaminate refinery catalysts, so the nitrogen value in the vacuum gas oil gives planners an early read on how demanding hydrotreating or hydrocracking will be. Nickel and vanadium in the vacuum residue raise the same catalyst concern, while carbon residue gives an indication of the residue’s tendency to form coke.
Full Assays Compared to Short Assays and Flash Assays
Not every crude oil assay report carries the same depth of data. The scope is usually set by a template agreed with the end user before testing starts, and common levels are compared below. Laboratories name them differently, so the descriptions matter more than the labels.
| Assay type | What it typically includes | When it is used |
| Full (Comprehensive) Assay | Whole-crude properties, physical distillation by ASTM D2892 and ASTM D5236, and distillation yields with detailed testing of each cut | Evaluating a new grade, or building and updating the reference data used in planning models |
| Short (Evaluation) Assay | Whole-crude properties, physical distillation by ASTM D2892 and ASTM D5236, and distillation yields, with fewer cut tests than a full assay | A quicker evaluation of a grade when full cut-by-cut detail is not needed |
| Flash (Monitor) Assay | Key whole-crude properties plus a boiling point curve and yields from ASTM D7169 gas chromatography | Screening crudes of interest, or monitoring a known grade to decide whether a full assay update is needed |
The practical difference shows up in the cut data. Full and short assays produce physical fractions that can each be tested, so their cut properties are measured directly. A flash assay relies on a boiling point curve from gas chromatography, which gives a useful picture of potential yields but no distillation cuts are produced for testing.
Comparing the new boiling point data with the reference assay determines when a full assay update is due.
Frequently Asked Questions About Crude Oil Assay Reports
Is crude oil assay analysis the same as crude oil characterization?
The terms overlap and are often used interchangeably. Crude oil characterization describes the broader work of defining a crude’s physical and chemical makeup, while an assay is the structured set of tests behind it and the report that presents the results.
How is Atmospheric Equivalent Temperature (AET) defined in a report?
Vacuum distillation runs at reduced pressure, so the vapor temperatures observed in the still are lower than the crude’s boiling points at atmospheric pressure. AET converts those readings to the equivalent atmospheric temperature, which puts cut points from both distillation stages on one scale. ASTM D2892 includes a practice for this conversion as an annex.
Is a published crude oil assay example enough to value a specific cargo?
A published or reference assay describes a grade in general terms, and individual cargoes can differ from it. Testing the cargo, or monitoring it against the reference assay, confirms whether the published data still applies.
Putting Crude Oil Assay Data to Work
A crude oil assay report is most useful when each layer is read in context. Whole-crude properties give the first screen, the yield table shows how the barrel splits, and the cut data indicates how each fraction is likely to perform in the unit it feeds.
AmSpec provides crude oil testing, sampling, and independent inspection for cargo tankers, pipelines, storage tanks, and refineries. Its crude oil assay services range from flash assays and short assays to full assays, with reports tailored to each client’s needs. To talk through assay scope for a specific grade or cargo, contact the AmSpec team.